喷砂机在运用过程中需留意以下几个留意事项
Sandblasting machine in the application process should pay attention to the following considerations
一、砂量少，以至不出砂：储砂桶里的砂材耗光了，关掉气，渐渐再参加相应的砂材就能够了。还有一种可能是磨料阀门因空气内有水气与磨料板结招致磨料阀阻塞，切记磨料时不能大于喷砂机枪嘴口径的2/3。
A little sand, not even sand: sand storage barrels in the sand consumption of light, turn off the gas, and gradually take part in the corresponding sand material can be. There is a possibility of air gas valve due to abrasive and abrasive abrasive to harden valve block, not greater than the blast gun caliber 2/3 remember abrasive nozzle.
二、喷砂机的喷砂枪有可能梗塞：停气后，取下喷嘴，看有没有异物，有的话将异物清算洁净就行了；还有就是要看砂材能否干燥，砂材过于湿润也会形成梗塞的状况，所以紧缩空气一定要枯燥。倡议用户在受用前装备一台冷干机为保证紧缩空气的枯燥。
Two, sand blasting gun of sandblasting machine may jam: stop gas, remove the nozzle, to see if there is no foreign body, any foreign body clean on the line; there is to see whether the dry sand material, sand material too wet will form infarction condition, so the compressed air must be boring. All users in the initiative before is equipped with a cold and dry machine to ensure the air dry.
三、喷砂管被梗塞：管子被赃物梗塞，停气关掉气后，喷嘴先取下来，然后再翻开喷砂机，用空压机的高压气体将异物吹出来；还是没有效果的话，就要将管子拆下来清算或者换新了。
Three, sandblasting pipe pipe was stolen by infarction infarction, turn off the gas stop gas nozzle, take down, and then open the sandblasting machine, with high pressure gas compressor will blow out; or no effect, will remove the pipe liquidation or renewed.
四、喷砂磨料湿润分离形成不出砂，这个把喷枪喷嘴清算洁净，喷砂磨料倒出来，晒干后用筛网过滤下即可。
The separation of four, wet sand abrasive blasting form, the spray gun nozzle clean, abrasive blasting poured out, dried with the mesh filter can.
五、与喷砂机配套的空压机紧缩空气产生的大量水份，这个不但会形成砂材湿润，还会形成喷砂管壁湿润而粘附砂材，渐渐梗塞管道，所以应该防止此类事情发作，最好装备干燥机。
A lot of water tight air compressor five, sandblasting machine and ancillary production, this will not only form wet sand material, but also the formation of a blast pipe wall wet adhesion sand material, gradually plug the pipe, so it should prevent such things happen, the best drying equipment.
六、喷砂砂料没有滤网形成较大异物或不平均砂粒进入砂阀，这个要先把推力安装关掉，调砂阀全部翻开，压力罐冲后翻开喷砂机，用强压空气把异物或结块的砂材扫除；还是不行的话，只能把磨料阀卸掉，把砂放出来，然后把调砂设备缩回去；再把砂材过滤，重新加进去就行了。
Six, there is no filter material sand blasting sand to form a larger foreign body or uneven sand into the sand valve, the first to install thrust off, adjust the sand valve opening, the pressure tank after open sandblasting machine, using forced air to remove foreign body or caking sand material; or if not, only the abrasive valve off the sand is put out, and then adjust the sand equipment back; the sand material filter, to add on the line.
七、加砂一次性太多，加砂超负荷也会形成梗塞而不能加压吸砂；所以加砂的时候，一定要留意量要适宜。
Seven, add sand too much, plus sand overload will form infarction and can not pressure suction sand; so add sand, we must pay attention to the amount to be suitable.

了解更多详情，请搜索：烤漆房,喷塑烤房,环保除尘设备 济南华誉涂装设备有限公司 http://www.huayutuzhuang.com/ 欢迎您的光临！