有些车辆在喷塑烤房内喷涂和烤漆之后，漆面上会出现一些麻点，仔细观察会发现是一些尘埃颗粒被油漆包裹附着在漆面上。当呈现这种状况时，就阐明喷塑烤房内的空气中含有许多的尘埃。
Some vehicles in the baking room and spray spray paint, some pits will finish, careful observation will find some dust particles are attached to the finish paint package. When present this situation, that spray baking room air contains a lot of dust.
(1)进入喷塑烤房的空气是污染物的主要来历。在不运用喷塑烤房时，应当将喷塑烤房的门关好，禁止使喷塑烤房的门长时间处于翻开的状况。在许多修理厂中，腻子的打磨作业通常在间隔喷塑烤房很近的区域内进行，打磨腻子的进程中会发生许多的粉尘，许多的腻子灰等粉尘跟着空气的流动很容易进入喷塑烤房。假如腻子打磨采纳了无尘干磨技能，状况会相对好一些，假如采纳的是手艺打磨方法，污染就会十分严峻。因而，在修理厂中，腻子打磨作业应当在远离喷塑烤房的区域进行。
(1) enter the spray baking room is a major source of air pollutants. Do not use in the spray baking room, should be sprayed barn door closed, the prohibition of the barn door with a long time in the open state. In many repairs, grinding operation putty usually in the baking room is near the spray interval in the region, many of the dust in the process of polishing putty, putty and so many dust with the air flow easily into the spray baking room. If the adoption of clean dry grinding polishing putty skills, conditions will be relatively better, if adopt the craft grinding method, pollution will be very serious. Therefore, in the garage, putty grinding operation shall be carried out in the area away from spray baking room.
(2)喷塑烤房作业时，通气电扇会将外界的空气抽入，经过喷塑烤房顶棚上的过滤棉向下吹，空气从烤漆房地板上被抽出喷塑烤房，喷塑烤房内就制作出了下降气流，这么，喷塑烤房内即使有少数的尘埃，也不会飞扬起来。喷塑烤房顶棚上的过滤棉可以过滤掉大多数的尘埃，然后坚持进入烤漆房内空气的清洁。因而，应当定时替换喷塑烤房顶棚上的过滤棉和烤漆房地板上的吸附棉。
(2) spray baking room operation, ventilation fan will be outside the air inlet, through the filter cotton spray baking room on the roof of blowing down, the air is pumped from the paint room floor spray baking room, spray baking room will produce a downdraft, so, spray the baking room even though a few the dust can not fly up. Filter cotton spray baking room the ceiling can filter out most of the dust, and then stick in the clean air into the baking room. Therefore, should replace the timing of adsorption on the roof of the barn with cotton filter cotton and paint room on the floor.
(3)待喷涂车辆本身通常是烤漆房内最大的污染源。车轮、保险杠以及发动机舱等部位会集合许多的污染物，完全的车身清洁作业可以使这些污染物对喷漆操作的影响下降。因此，车身清洁等杰出的准备作业是十分主要的。
(3) to be sprayed the vehicle itself is usually the biggest source of pollution in the paint room. Wheels, bumpers, and the engine compartment, and other parts of the collection of a large number of pollutants, full body cleaning operations can make the impact of these pollutants on the painting operation. Therefore, the body cleaning and other outstanding preparatory work is very important.
(4)喷漆操作人员穿戴的作业服也是主要的污染源。在许多修理厂，打磨腻子和喷涂漆面的作业是由同一自己完结，许多工人在打磨腻子时和喷涂漆面时穿戴同一套作业服，这是不正确的，在喷涂漆面时应当有专用的作业服。在烤漆房内，应当穿戴无纤维掉落的作业服，戴橡皮手套、防护面罩和呼吸器，在喷涂各道漆面时都要坚持这么的穿戴。没有穿专用作业服的人员禁止进入烤漆房，而只能从窥视窗观看喷漆作业，避免污染油漆。
(4) the operating clothing worn by the painting operator is also a major source of pollution. In many repair factory, polishing putty and paint spraying operation is completed by the same, many workers and spraying paint when wearing the same set of work clothes in abrading putty, this is not true, in the spray paint should have special work clothes. In the baking room, should wear no fiber from work clothes, wearing rubber gloves, protective masks and respirators, spraying the paint on to wear so. Do not wear clothes for special operation personnel are prohibited from entering the paint room, and only from the peep window view of spray paint, avoid pollution.
(5)除了隐瞒车身和喷涂等必须在烤漆房内完结的作业以外，别的车身准备作业和油漆分配作业应当在烤漆房外面进行。有些修理厂甚至在烤漆房内清洁车辆或打磨腻子，这是严峻违反修补漆操作标准的做法。
(5) in addition to hide the body and spray paint room must be at the end of the operation, other body preparation and distribution operations shall be carried out in the paint baking room outside. Some repair plant even in the baking room cleaning vehicle or polishing putty, this is a serious violation of the standard practice operation repair paint.
(6)喷枪等喷涂设备要坚持清洁。应当在每次喷涂作业后及时清洁喷枪，避免喷枪内的油漆枯燥，油漆干燥后会凝聚成片，假如枯燥成片的油漆在喷涂时飞出，将在漆面上构成缺点。
(6) spraying equipment such as spray gun should be kept clean. Shall promptly clean spray gun in each spraying operation, avoid spray paint dry, paint drying will be condensed into a boring if flying in the paint spraying, will constitute the shortcomings in the finish.
(7)在每次喷漆作业完结后应打扫烤漆房的地板和墙壁，将隐瞒车身时运用的隐瞒物等物品整理洁净。喷漆时应尽量运用一次性的隐瞒物隐瞒车身，尽量不要运用棉质的隐瞒车衣和车轮罩，由于这种车衣简单集合尘埃。
(7) in each spray paint room should be cleaned after the end of the floor and walls will hide the body by concealing materials clean. Spray paint should be used as much as possible to conceal the use of a concealed body, as far as possible not to conceal the use of cotton clothes and wheel cover, because of the simple collection of dust.
(8)喷塑烤房内不该放置零部件和油漆罐等杂物，由于这些东西会累积污物而终究污染待喷涂车辆。喷枪、纸胶带、腻子、车衣以及作业服等物品不该当存放在敞开的环境中，这些物品都应当放在密闭和通风的贮存室内。
(8) placing parts and paint cans and other debris should not spray baking room, because these things will eventually be accumulated dirt and pollution spraying vehicle. Spray gun, paper tape, putty, sewing and work clothes and other items should not be stored in the open environment, these items should be placed in the storage chamber and the airtight ventilation.
总归，为了确保轿车喷漆的质量，一定需要有专业的喷塑烤房及对于内环境的保护和严厉的操作标准是十分必要的。
After all, in order to ensure the quality of car paint, need professional spray baking room and for the protection of the environment and strict operating standards is necessary.